Disclosure: This post is sponsored by Plaid®. All opinions are my own.

I have had such a fun time collaborating on this fun Plaid project along with the other Plaid Creators, and I’ve been looking forward to finally sharing it with you! The rest of the Plaid Creators and I each designed and created a couple of items for a family room makeover, and then everybody shipped their creations to Atlanta and we set up an entire room in my house. Then, a photographer came to shoot it for Plaid. The entire project was so much fun! Today I’m sharing a tutorial for the DIY faux concrete and gold leaf planter that I built for the room. I love that it is a little bit industrial and modern, with the added “glam” factor of the gold leaf. Also, I’ll share a peek at the room reveal, and the most exciting part is that you can enter to win the ENTIRE gallery wall full of art that we made! I am so excited about this giveaway! Not only that, the grand prize winner will also win $500 in arts and crafts supplies. (See epic giveaway at the end of this post.) Also, be sure to head over to Plaid® to see tons more photos of the reveal!

Plaid Creators Family Room Reveal

First, let’s talk about the room! Here is the family room full of DIY projects that we collaborated on:

I created the tree string art for the gallery wall, and the planter (tutorial included in this post).

DIY Faux Concrete & Gold Leaf Planter

Project Supplies:

1 – 2×2 cut into (4) 15″ long pieces
1 – 1×2 cut into (5) 12″ long pieces (cut to fit)
1 – 2×12 cut into (4) 12″ long pieces
(16) 3″ wood screws
(10) 2 1/2″ wood screws
Countersinking drill bit
Drill
Saw (Miter Saw or circular saw work best, but a hand saw will do.)
FolkArt® Painted Finishes in Concrete
FolkArt® Shortie Brushes
Plaid® Liquid Leaf in Classic Gold
Small paintbrush
Painter’s Tape for textured surfaces
Paper plate
Putty knife
Wood filler
Sandpaper or sanding block
(Optional) Landscaping fabric

Step 1

First, cut your boards. I prefer using a miter saw, but a circular saw or a hand saw will work too. You will cut 1 – 2×12 board into 4 segments, each at 12″ long; 1 – 2×2 board into 4 segments, each at 15″ long; and 1 – 1×2 board into 5 segments, each at 12″ long.

Step 2

Using your 3 inch screws, attach two of the 2×2 pieces to each side of a 2×12 piece, forming one of the sides of the planter. Countersink the screws with a countersinking drill bit so you’ll be able to patch over them later. Repeat this with the other two legs and one of the 2×12 pieces, so you should have two that look like this:

Step 3

Using the remaining 2×12 pieces, join the two side segments together by attaching them with 3″ screws. Be careful to stagger the placement of your screws so you don’t run into the screw you’ve already drilled in when connecting the legs.

Step 4

Attach the 1×2 pieces by evenly spacing them and attaching them to the bottom. Attach them at each end using 2 1/2″ screws drilled from the outside of the planter. (Note: You can use pocket holes if you’d prefer.)

Step 5

Patch over your screws using a putty knife and wood filler, and then sand smooth.

Step 6

Now it’s time to paint! I used FolkArt® Painted Finishes in Concrete.

It comes in “Light” and “Dark”. Pour a little bit of each onto a paper plate which you can use as your palette.

Then, stipple on the light color with a Shortie brush, covering the entire planter.

Step 7

Working in sections, one side at a time, stipple some of the dark lightly on top of the light color while it’s still wet, blending and pouncing your brush as you go.

Step 8

After the concrete painted finish has dried, tape off your diagonal design using painter’s tape for textured surfaces. (You can find this at the hardware store.) I created an alternating diagonal, so on one side I had the diagonal running from the top left corner to the bottom right corner, and then on the next side I started where I left off, so that one would run from bottom left corner to the top right corner, and I continued with that pattern all the way around. Make sense? I hope so!

Step 9

Paint the bottom section below your tape with Plaid Liquid Leaf in Classic Gold. A little bit goes a long way, so even though the bottle is tiny, there is plenty in there. I used a small paintbrush to apply it and it only took one coat.

Step 10

Remove your tape while the liquid leaf is still somewhat damp, but not soaking wet as you don’t want it to bleed.

Step 11

Insert your plant, and enjoy! I opted to just drop the planter that my fiddle leaf fig came in directly inside this one, but you could also add a layer of landscape fabric and then your soil and plant on top of that.

Epic Plaid® Giveaway!

Enter to win this ENTIRE gallery wall full of DIY art made by the Plaid Creators! You could win every single piece of art you see hanging on the wall here:

PLUS, not only will the grand prize winner walk away with all of this original art, they will also win $500 worth of arts and crafts supplies from Plaid.

Grand Prize: Collection of gallery wall art AND $500 in arts & crafts supplies from Plaid
2nd Place: $200 in arts and crafts supplies from Plaid
3rd Place: $100 in arts and crafts supplies from Plaid

And here’s a fun little stop motion video of me hanging the gallery wall!

To enter the giveaway, simply follow the instructions in the Rafflecopter widget below. U.S. entrants only, must be 18+ years old. The giveaway ends 11/30/16.

a Rafflecopter giveaway

You Might Also Like: